Bad Sector (Hdd)

Kısaca: Bozuk kesim (ing. bad sector) veri depolama aygıtlarında fiziksel hasara uğrayarak işlevini yitiren kesimlerdir. Veri depolama aygıtlarında en küçük mantıksal depolama birimi kesimlerdir. Bir kesim normal ayırmada 512 bayttır. (bkz. iz-kafa-kesim) Bu alanlardan bazıları zamanla fiziksel hasara uğrayarak işlevini yitirir. Bozuk kesimler biçimlendirme sırasında tespit edilerek işaretlenir ve o kesimler kullanılmaz. Böylece "göz göre göre" veri kaybı önlenir. Diğer bir senaryo ile zaten yazılı olan ...devamı ☟

Bozuk kesim (ing. bad sector) veri depolama aygıtlarında fiziksel hasara uğrayarak işlevini yitiren kesimlerdir. Veri depolama aygıtlarında en küçük mantıksal depolama birimi kesimlerdir. Bir kesim normal ayırmada 512 bayttır. (bkz. iz-kafa-kesim) Bu alanlardan bazıları zamanla fiziksel hasara uğrayarak işlevini yitirir. Bozuk kesimler biçimlendirme sırasında tespit edilerek işaretlenir ve o kesimler kullanılmaz. Böylece "göz göre göre" veri kaybı önlenir. Diğer bir senaryo ile zaten yazılı olan bir kesimin fiziksel olarak bozulması durumunda oluşan bozuk kesim durumunda o kesimde yazan veri kaybolacaktır. Bunun sonucunda o kesimde yazan veri her ne ile ilgiliyse o çalışmayacak ya da yanlış çalışacaktır. Bozuk Kesimlerin Düzeltilmesi Bozuk kesimlerin düzeltilmesi mümkün değildir. Eğer veri depolama aygıtınızda bozuk kesim olarak işaretlenmiş bölümlerin işaretlerini kaldırırsanız, kesimler bozuk olarak görünmeyecektir. Bu işlemin bozuk kesimi tamir etmekle bir ilgisi olmayıp çok yanlış bir uygulamadır. Zira bu bozuk kesim olarak işaretlenmiş bölgeye kayıt yapılması durumunda veri kaybı söz konusu olacaktır. Ancak tabiki bir yolu vardır. LLF yani düşük seviye format atılarak bad sectorler tamir edilebilir. Low Level Format LLF harddisktekiplakaların üstlerinin kazınmasıdır. Bu işlem %70 risklidir. Çünkü bir elektrik kesilmesi, dalgalanma veya kilitlenmede HDD %70-80 oranında geri dönülmez şekilde bozulacaktır. Bu işlem bir ufak titreme ile bile HDD'yi bozabilir. LLF sadece uzman kişiler tarafından yapılmalıdır. Aksi takdirde acemi biri 1TBlik bir harddiski yaktığında ağır bir depresyona girebilir. MaxBlast isimli program ile bu işlem gerçekleştirilebiliyor. A bad sector is a sector on a computer's disk drive or flash memory that cannot be used due to permanent damage (or an OS inability to successfully access it), such as physical damage to the disk surface (or sometimes sectors being stuck in a magnetic or digital state that cannot be reversed) or failed flash memory transistors. It is usually detected by a disk utility software such as CHKDSK or SCANDISK on Microsoft systems, or badblocks on Unix-like systems. When found, these programs may mark the sectors unusable (all file systems contain provisions for bad-sector marks) and the operating system skips them in the future. If any of the files uses a sector which is marked as 'bad' by disk utility then the bad sector of the file is remapped to a free sector and any unreadable data is lost. To avoid file corruption data recovery methods should be performed first if bad sectors are found (before being marked) by OS at file system level. When a sector is found to be bad or unstable by the firmware of a disk controller, the disk controller remaps the logical sector to a different physical sector. In the normal operation of a hard drive, the detection and remapping of bad sectors should take place in a manner transparent to the rest of the system and in advance before data is lost. There are two types of remapping by disk hardware; P-LIST (Mapping during factory production tests) and G-LIST (Mapping during consumer usage by disk microcode). There are a variety of utilities that can read the SMART information to tell how many sectors have been reallocated, and how many spare sectors the drive may still have. Because reads and writes from G-list sectors are automatically redirected (remapped) to spare sectors it slows down drive access even if data in drive is defragmented. If the G-list is filling up, it is time to replace the drive. Typically, automatic remapping of sectors only happens when a sector is written to. The logic behind this is presumably that even if a sector cannot be read normally, it may still be readable with data recovery methods. However, if a drive knows that a sector is bad and the drive's controller receives a command to write over it, it will not reuse that sector and will instead remap it to one of its spare-sector regions. This may be the reason why hard disks continue to have sector errors (mostly disk controller timeouts) until all the bad sectors are remapped; typically this is accomplished by writing zeros to the entire drive. See the SMART attribute number 197 ("Current Pending Sector Count") for more information. See also *Sector slipping, a method of avoiding bad sectors. Software to fix the bad sector problem: chkdsk and format (without quick option) are the tools accompanying Windows, which can be used to check for bad sectors and mark them bad. FBDISK can isolate the bad sectors and partition the remaining area to at most four partitions. It is run in DOS. Similar to FBDISK, PBD (Partition Bad Disk) also isolates bad sectors on HDD and creates healthy partitions. It is run in Windows and provides other partitioning functionalities. References External links * Bad Blocks Definition * Bad Sector Remapping Techniques * Bad sector corruption Hard disk computer storage Solid-state computer storage

Bu konuda henüz görüş yok.
Görüş/mesaj gerekli.
Markdown kullanılabilir.